How many watts does Starlink Mini use?

Internet Also called: starlink, satellite internet, dishy

Two numbers decide whether a power station runs a Starlink Mini, and readers arrive using them interchangeably. Watts are the ceiling on what the inverter can hold at any instant — this load needs 40 W of them while it runs, and 60 W for the moment it starts. Watt-hours are how much energy the battery holds, and this load gets through about 960 Wh in a day. A machine can have plenty of one and not enough of the other.

Of the 26 station records we publish — every model we hold a page for, with its US and EU versions counted separately — 26 run it, 0 are a tight fit and 0 are out of reach. Each of those is a calculation against that machine’s continuous output, its surge ceiling and its inverter waveform — not a lookup table — and the reasoning is on every row.

The three numbers a power station is judged against

Running power 20–40 W Official spec · verified 2026-08-01 · medium confidence

This machine has no single running wattage — the band is its own, not a spread across models. Every verdict below is computed at the top of it, 40 W.

Start-up surge 60 W engine checks 60 W Official spec · verified 2026-08-01 · medium confidence

Duty cycle 100% Official spec · verified 2026-08-01 · high confidence

This band is one machine turning itself up and down, not a spread across models, so there is no “which unit do I own” to resolve here. Where it sits moves with the conditions the machine is working in, which is why the runtimes below come out as intervals rather than as one number.

Start-up figure: Manufacturer-stated

The start-up figure is published by the manufacturer for this device, so it describes the actual hardware rather than a category.

Official specverified 2026-08-01appliance record

What actually decides it

A switch-mode supply: milliseconds, not seconds

A switching power supply charges its input capacitors at the instant it is connected, which can be a large current — but it lasts a few line cycles, two orders of magnitude shorter than the second-scale event a station’s surge rating describes. The two are not the same quantity and this site does not hold that spike against a verdict. What decides the outcome here is the steady draw, and where the power factor is poor, the VA the inverter actually sees behind it.

It does not have one running wattage

This machine does not have one running wattage: the record carries a low, a rated and a high point off the same nameplate. The runtime below is worked out from that curve rather than from a duty cycle, so it comes out as an interval. A single number would be a choice we made on your behalf about which setting, or which conditions, you are running it in.

Which power stations run it

Every row is a live calculation against that machine's continuous output, surge ceiling and inverter waveform. Of the 26 station records we publish — US and EU versions counted separately — 26 run it, 0 are a tight fit and 0 are out of reach. The percentage is this load as a share of that machine's continuous output; anything past 82% drops out of the green. Rows are ordered by verdict, then by price — cheapest first inside each band.

BLUETTI Elite 30 V2 BLUETTI · US 120 V 600 W continuous Runs it6.7%

5.0–8.5 h — on a full charge, with the station’s own 9.0 W idle draw in the denominator We have found no published surge rating for the US 120 V build. The start-up check runs against its continuous output as a conservative floor, which is ours, not a manufacturer specification. $239 · checked 2026-08-17 Show the working →

EcoFlow RIVER 3 Plus EcoFlow · US 120 V 600 W continuous · 1,200 W surge ceiling Runs it6.7%

40 Wh per hour — averaged over this load’s duty cycle No runtime in hours: 4 of EcoFlow’s own published documents, read 2026-08-08, carry no depth of discharge or inverter efficiency for the US 120 V build, so there is no defensible usable-capacity figure to divide. $279 · checked 2026-08-17 Show the working →

Jackery Explorer 300 Plus Jackery · US 120 V 300 W continuous · 600 W surge ceiling Runs it13%

4.4–7.2 h — on a full charge, with the station’s own 12 W idle draw in the denominator $299.99 · checked 2026-08-17 Show the working →

BLUETTI Elite 100 V2 BLUETTI · US 120 V 1,800 W continuous · 3,600 W surge ceiling Runs it2.2%

17–28 h — on a full charge, with the station’s own 10 W idle draw in the denominator $499 · checked 2026-08-17 Show the working →

Jackery Explorer 1000 v2 Jackery · US 120 V 1,500 W continuous · 3,000 W surge ceiling Runs it2.7%

15–23 h — on a full charge, with the station’s own 18 W idle draw in the denominator $549 · checked 2026-08-17 Show the working →

EcoFlow DELTA 3 Plus EcoFlow · US 120 V 1,800 W continuous · 3,600 W surge ceiling Runs it2.2%

BLUETTI Elite 200 V2 BLUETTI · US 120 V 2,600 W continuous Runs it1.5%

32–53 h — on a full charge, with the station’s own 10 W idle draw in the denominator We have found no published surge rating for the US 120 V build. The start-up check runs against its continuous output as a conservative floor, which is ours, not a manufacturer specification. $899 · checked 2026-08-17 Show the working →

Jackery Explorer 2000 Plus Jackery · US 120 V 3,000 W continuous · 6,000 W surge ceiling Runs it1.3%

25–36 h — on a full charge, with the station’s own 25 W idle draw in the denominator $899 · checked 2026-08-17 Show the working →

Jackery Explorer 1000 Plus Jackery · US 120 V 2,000 W continuous · 4,000 W surge ceiling Runs it2.0%

16–24 h — on a full charge, with the station’s own 22 W idle draw in the denominator $999 · checked 2026-08-17 Show the working →

EcoFlow DELTA 2 Max EcoFlow · US 120 V 2,400 W continuous · 4,800 W surge ceiling Runs it1.7%

40 Wh per hour — averaged over this load’s duty cycle No runtime in hours: 5 of EcoFlow’s own published documents, read 2026-08-08, carry no depth of discharge or inverter efficiency for the US 120 V build, so there is no defensible usable-capacity figure to divide. $1,049 · checked 2026-08-17 Show the working →

EcoFlow STREAM Ultra EcoFlow · US 120 V 800 W continuous Runs it5.0%

40 Wh per hour — averaged over this load’s duty cycle No runtime in hours: 3 of EcoFlow’s own published documents, read 2026-08-08, carry no depth of discharge or inverter efficiency for the US 120 V build, so there is no defensible usable-capacity figure to divide. We have found no published surge rating for the US 120 V build. The start-up check runs against its continuous output as a conservative floor, which is ours, not a manufacturer specification. $1,279 · checked 2026-08-17 Show the working →

EcoFlow DELTA Pro 3 EcoFlow · US 120 V 4,000 W continuous · 8,000 W surge ceiling Runs it1.0%

BLUETTI Elite 30 V2 BLUETTI · EU 230 V 600 W continuous Runs it6.7%

5.0–8.5 h — on a full charge, with the station’s own 9.0 W idle draw in the denominator We have found no published surge rating for the EU 230 V build. The start-up check runs against its continuous output as a conservative floor, which is ours, not a manufacturer specification. €219 · checked 2026-08-17 Show the working →

Anker SOLIX C300 Anker SOLIX · EU 230 V 300 W continuous · 600 W surge ceiling Runs it13%

40 Wh per hour — averaged over this load’s duty cycle No runtime in hours: we have found no depth of discharge or inverter efficiency for the EU 230 V build, so there is no defensible usable-capacity figure to divide. €269.99 · checked 2026-08-01 · 17 days ago Show the working →

Jackery Explorer 300 Plus Jackery · EU 230 V 300 W continuous · 600 W surge ceiling Runs it13%

EcoFlow RIVER 3 Plus EcoFlow · EU 230 V 600 W continuous · 1,200 W surge ceiling Runs it6.7%

40 Wh per hour — averaged over this load’s duty cycle No runtime in hours: we have found no depth of discharge or inverter efficiency for the EU 230 V build, so there is no defensible usable-capacity figure to divide. €299 · checked 2026-08-01 · 17 days ago Show the working →

Jackery Explorer 1000 v2 Jackery · EU 230 V 1,500 W continuous · 3,000 W surge ceiling Runs it2.7%

BLUETTI Elite 100 V2 BLUETTI · EU 230 V 1,800 W continuous Runs it2.2%

17–28 h — on a full charge, with the station’s own 10 W idle draw in the denominator We have found no published surge rating for the EU 230 V build. The start-up check runs against its continuous output as a conservative floor, which is ours, not a manufacturer specification. €579 · checked 2026-08-17 Show the working →

EcoFlow STREAM Ultra EcoFlow · EU 1,200 W continuous Runs it3.3%

40 Wh per hour — averaged over this load’s duty cycle No runtime in hours: we have found no depth of discharge or inverter efficiency for the EU build, so there is no defensible usable-capacity figure to divide. We have found no published surge rating for the EU build. The start-up check runs against its continuous output as a conservative floor, which is ours, not a manufacturer specification. €599 · checked 2026-08-17 Show the working →

EcoFlow DELTA 3 Plus EcoFlow · EU 230 V 1,800 W continuous · 3,600 W surge ceiling Runs it2.2%

EcoFlow DELTA 2 Max EcoFlow · EU 230 V 2,400 W continuous · 4,800 W surge ceiling Runs it1.7%

Anker SOLIX Solarbank 3 E2700 Pro Anker SOLIX · EU 1,200 W continuous Runs it3.3%

Jackery Explorer 1000 Plus Jackery · EU 230 V 2,000 W continuous · 4,000 W surge ceiling Runs it2.0%

BLUETTI Elite 200 V2 BLUETTI · EU 230 V 2,600 W continuous Runs it1.5%

33–54 h — on a full charge, with the station’s own 13 W idle draw in the denominator We have found no published surge rating for the EU 230 V build. The start-up check runs against its continuous output as a conservative floor, which is ours, not a manufacturer specification. €1,149 · checked 2026-08-17 Show the working →

Jackery Explorer 2000 Plus Jackery · EU 230 V 3,000 W continuous · 6,000 W surge ceiling Runs it1.3%

EcoFlow DELTA Pro 3 EcoFlow · EU 230 V 4,000 W continuous · 8,000 W surge ceiling Runs it1.0%

Which one to buy, ranked

Our pick for this load

BLUETTI Elite 30 V2 · US 120 V

The cheapest US 120 V machine in the list that runs a Starlink Mini outright, and it holds it at 5.0–8.5 h.

$239 · price checked 2026-08-17

The buy link is in the bar at the bottom of the screen — one action per page, and it goes to the merchant we last checked the price at.

Everything else we hold on this load

Each figure carries the tier it came from and the date it was checked. Sizing guidance is kept apart from measured draw on purpose: one says what the machine pulls, the other says what a manufacturer or a standard thinks you should buy for it.

Measured and published draw

Standby draw 15 W Official spec · verified 2026-08-01 · high confidence

Energy per day 960 Wh Derived from official coefficients · verified 2026-08-01 · medium confidence

Not a published figure: computed from this load’s running draw and its duty cycle, which is why its confidence sits below the specs around it.

Sizing guidance — not a draw figure

Minimum continuous output 60 W Official spec · verified 2026-08-01 · high confidence

A sizing figure, not a draw: it is what this class needs a machine to be RATED at, headroom included.

Usable energy for a full day 960 Wh Derived from official coefficients · verified 2026-08-01 · medium confidence

Where to go next

From the Knowledge channel

A Starlink Mini has a dedicated guide: the same records this page computes from, worked through in prose with room for the reasoning a table can only summarise — What size power station do you need to keep a Starlink Mini running?

Questions people ask about this load

How many watts does a Starlink Mini use?

20–40 W while it is running, with 60 W demanded at the instant it starts. Those are different questions and most pages answer only the first. The running figure decides whether a machine can hold it; the start-up figure decides whether it can get it going at all, and it is usually the one that fails. The start-up figure here is the manufacturer’s own..

What size power station do I need for a Starlink Mini?

For a Starlink Mini, the BLUETTI Elite 30 V2 (US 120 V) is the cheapest machine in our library that runs it, at 600 W continuous and $239 against a running draw of 20–40 W and a start-up demand of 60 W. That is a verdict computed from this load’s running watts, its start-up demand and the inverter waveform — not a rule of thumb about doubling the wattage. 26 of 26 machines clear it.

How long will a power station run a Starlink Mini?

It depends entirely on the machine, which is the part most pages skip. Against a Starlink Mini at 20–40 W of running draw, our figures put the BLUETTI Elite 30 V2 at about 5.0–8.5 h, and the Jackery Explorer 300 Plus at about 4.4–7.2 h. Those hours come from usable-capacity figures derived from each manufacturer’s own published usable-capacity coefficients — depth of discharge and inverter efficiency where a brand states them separately, with each machine’s idle draw in the denominator — not from dividing a nameplate watt-hour number by a label wattage. Most machines in the list carry no hours at all: we hold nothing for those builds that makes a usable-capacity figure defensible, so those rows give an energy rate instead of a number we would have had to invent.

Why does a Starlink Mini need so much more power to start?

The start-up figure is published by the manufacturer for this device, so it describes the actual hardware rather than a category. The engine works the check against 60 W, which is what a station's surge ceiling has to cover for the moment the machine starts. A station whose continuous rating is comfortably above the running figure can still refuse the start, and that is the single most common way a purchase goes wrong for this class.

Which power stations run a Starlink Mini?

26 of the 26 we hold, listed above cheapest-first within each verdict band, starting with the BLUETTI Elite 30 V2. All 26 of them run a Starlink Mini. Every one of those is a live calculation against that machine's own record, and opening a row shows the working.