Will an Anker SOLIX C300 run a CPAP machine? (EU 230 V)

Tight fit no usable-capacity figure see why below ↓

This load’s manufacturer asks for a pure sine wave and we have found no published inverter waveform for the EU 230 V build. The watts are not the problem — the refusal to assume a waveform is.

Official spec + Derived by WattPairverified 2026-08-01EU 230 V unit × CPAP machine

Nominal capacity 288 Wh
Surge headroom 10×+

Running22 Wof300 Wcontinuous output

0 – 300 W across the rails above

No start-up rail: this load has no locked rotor to publish an inrush for, so no start-up demand was checked.

Two numbers decide this, and readers use them interchangeably: watts are the ceiling on what the inverter holds at any instant, watt-hours are how much energy the battery holds. A machine can have plenty of one and not enough of the other.

The verdict is a calculation, not a lookup. What it will not do is print a runtime, and the reason is specific: we have found no published depth of discharge or inverter efficiency for the EU 230 V build, so there is no usable-capacity figure to divide.

This page answers an electrical question, not a medical one.

Where this page puts hours on a pairing, that figure is how long a power station’s battery lasts running this machine’s wattage — an electricity calculation, not a judgment about whether a break in therapy is safe. A small watt figure alone does not settle a verdict here either: this machine also carries a documented waveform requirement, and a station with no waveform on record is held at a tight fit regardless of how easily it clears the watts.

Where a verdict below reads a tight fit — the amber triangle on a row in the list of stations — read it as don’t rely on this pairing, whatever reason the row gives for that particular verdict, and not as a compromise likely to hold anyway. That state means the same thing here however it was arrived at: this site cannot clear the pairing with confidence, and that isn’t a passing grade with a footnote. Where a row says a check could not be run at all, that is a weaker claim than a near miss, not a stronger one.

What to do about a power interruption during therapy is a question for a clinician, the durable medical equipment (DME) supplier who set the machine up, or the manufacturer’s own guidance for it — not for this site. For the electricity side of an outage plan, this page can help: what a station needs to run this machine at all, and — where both makers publish enough to work it out — how long a given battery keeps it running.

Where those numbers come from

A blank is never left blank. A field we have found no figure for says so, and a field whose sources disagree — two documents, or one document with itself — says that instead of picking one.

No usable-capacity figure for this machine

Anker SOLIX states a nameplate watt-hour number for it, and we have found no published depth of discharge or inverter efficiency for the EU 230 V build. Dividing the nameplate by this load would be wrong by 20–35% in the flattering direction, so this page shows the nameplate for what it is and refuses to turn it into hours.

Missing: station.usable_capacity_wh

Energy rate instead of a runtime

22 Wh per hour averaged over this load’s duty cycle

This number needs no battery figure at all, which is why this page can give it when it cannot give hours. Divide any usable-capacity figure you trust by it and you have your own runtime, with our arithmetic visible instead of hidden.

What a CPAP machine demands

Running power 22 W Official spec · verified 2026-08-01 · high confidence
Duty cycle 100% Official spec · verified 2026-08-01 · high confidence
Power factor 0.50 Official spec · verified 2026-08-01 · high confidence

The inverter is loaded to 44 VA — 22 W ÷ 0.50 — which is the quantity its ceiling is actually measured against.

Pure sine wave required Yes Official spec · verified 2026-08-01 · high confidence

What the Anker SOLIX C300 offers

Continuous output 300 W Official spec · verified 2026-08-01 · high confidence
Surge ceiling 600 W Official spec · verified 2026-08-01 · high confidence
Nominal capacity 288 Wh Official spec · verified 2026-08-01 · high confidence

Where to buy

Where to buy the Anker SOLIX C300

Prices checked 2026-08-01 · checked 17 days ago

Anker SOLIX Official Store (EU) €269.99 View →

If this is not the pairing

Buy yourself some headroom

BLUETTI Elite 30 V2 (EU 230 V) — 600 W continuous, and it holds a CPAP machine for about 7.9 h · from €219. See that pairing →

The same load on the machines beside it

The same machine on the loads beside it

Where to go next

From the Knowledge channel

A CPAP machine has a dedicated guide: the same records this page computes from, worked through in prose with room for the reasoning a table can only summarise — How many nights can a power station run my CPAP?

Questions people ask about this pairing

Will an Anker SOLIX C300 run a CPAP machine?
Yes, but with very little room. 22 W of running draw against 300 W of continuous output — 7.3% of it. Anything past 82% of continuous output drops out of the green on this site, because a rating is a ceiling and a hot afternoon is not a laboratory. The verdict is computed from running watts — the working is in the evidence section above.
How long will an Anker SOLIX C300 run a CPAP machine?
We will not put a number on it, and that is a finding rather than a gap. We have found no published depth of discharge and no inverter efficiency for the EU 230 V build. What it does state is a nameplate watt-hour rating. Dividing that nameplate by this load produces a figure that is typically 20–35% too high while looking exactly as authoritative as a real one. What this page gives instead is the load's energy rate in watt-hours per hour, which needs no battery figure at all.

Tight fit Anker SOLIX C300 · from €269.99 · 17 days ago

Check price →